RK Flooring Systems Private Limited
Gurgaon, Haryana
Home»Products & Services»

Concrete Repairs

We are the suppliers of the Concrete Repairs. These products are available in the market at cost effective prices. Complete solution for concrete repairs based on cementations, polymer and resin based repair mortars. Proper application of concrete repairing materials on damaged portion prolonging the life of structures. These are available in the market according to the needs of the clients.


Epoxy Based Repair Mortar and Concrete - Nitomortar S

Epoxy Based Repair Mortar and Concrete - Nitomortar S
Epoxy Based Repair Mortar and Concrete - Nitomortar S

poxy based repair mortar and Concrete - Nitomortar S.

Description

High strength abrsasion resistance epoxy reinstatement mortar

Principal Use

Nitomortar S is used for the fast and permanent reinstatement of concrete, particularly where high strength abrashion resistance and resistance to chemicals is required.

Key Properties

Compressive Strength       60N/mm²

Tensile strength                  10N/mm²

Flexural strength                  20N/mm²

Pot Life at 35ºC                       20mins

Advantages:

  • High ultimate strength - Suitable for structural use

  • Early development of strength Minimises disruption

  • Abrasion resistance - Suitable for heavy traffic areas

  • Highly resistant - To a wide range of chemicals

  • Will cure under damp conditions - Cured product is highly impermeable to water

  • Typically twice as strong as good quality concrete

  • Pre-weighed components ensure consistency


Specification

 

Nitomortar S is based on a high quality solvent-free epoxy resin system. The special silica aggregates provide high strength and excellent abrasion resistance. Nitomortar S is a three - component material supplied in pre-weighed quantities ready for on-site mixing and use.

Cement Based Repair Mortar and Concrete

Cement Based Repair Mortar and Concrete
Cement Based Repair Mortar and Concrete

 Cement based repair mortar and concrete - Renderoc RG Spl
Description
Genral purpose,non shrink ,cementious micro concrete
Principal Use
Rendroc RG Spl is used for repair to damaged reinforced concrete element particularly where access is restricted and where vibration of the placed material is difficult or impossible
Key Properties
Compressive strength  75 N/mm²
Flexural strength         8N/mm²
Young module             25 KN/mm² 

Advantages:

  • Gaseous expansion system compensates for shrinkage and settlement in the plastic state.

  • Can be pumped or poured into restricted locations.

  • Fluidity to allow for placement without vibration.

  • Pre-bagged to overcome site-batched variations.

  • Rapid strength gain to facilitate early reinstatement.

  • High ultimate strengths and low permeability of cured repair.

  • Contains no chloride admixture.


Specification


Renderoc RG Spl is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-flowing non-shrink repair micro concrete. The material is based on Portland cements, graded aggregates and fillers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand.

Cement Based Repair Mortar and Concrete

Cement Based Repair Mortar and Concrete
Cement Based Repair Mortar and Concrete

 Cement based repair mortar and concrete - Renderoc LAXtra Plus.
Description
HIgh strength,dual shrinkage controlled polymer modified fluid microconcrete for structural repairs of all types
Principal Use
Rendroc LAxtra is suitable for mass infill to structural repairs in all types of load bearing situation.
Key Properties
 
Compressive Strength @28days    >65N/mm²
Flexural strengt @ 28Days            > 3N/mm²

Advantages:

  • Renderoc LAXtra Plus features Dimensional Stability Technology - a new materials technology which controls the rate of drying shrinkage such that, when used correctly :

  • the dimensions of the repair remain stable; and thus

  • ii. eliminating failure, due to shrinkage cracking.


Specification
Renderoc LAXtra Plus is supplied as a ready to use blend of dry powders and selected aggregates, which requires only the addition of clean water to produce a highly consistent, fluid micro concrete suitable for all load-bearing situations.

Epoxy Based Repair Mortar and Concrete - Nitomortar 30

Epoxy Based Repair Mortar and Concrete - Nitomortar 30
Epoxy Based Repair Mortar and Concrete - Nitomortar 30

Epoxy based repair mortar and Concrete - Nitomortar 30

Description

Chemical and abrasion resistant epoxy repair compound

Principal Use

For permanent repairs to concrete structure and cementious substrate where strength impermeability to water and resistance to aggressive chemical is essential

Key Properties

Pot Life at 30ºC                     30mins

Full Cure                                 7Days

Compressive strength            45 N/mm²

Tensile strength                    4.5 N/mm²

Bond strength                      3N/mm²


Advantages:

  • Chemical Resistance :Unaffected by wide range of acids, alkalis and industrial chemicals

  • Easily applied :Designed for easy application to a fair finish

  • Quality : Pre-weighed quality controlled materials ensure consistency and reduce risk of site errors

  • Proven performance : Successful use proves for a wide variety of aggressive applications


Specification


Nitomortar 30 is a three part solvent free combination of epoxy resin, modified amine hardeners filled with specially graded chemically inert aggregates with high crushing strength. It is applied by trowel as a durable chemical resistant repair mortar 3-6 mm thick depending upon the requirement.

Cement Based Repair Mortar And Concrete - Renderoc S2

Cement Based Repair Mortar And Concrete - Renderoc S2
Cement Based Repair Mortar And Concrete - Renderoc S2

Description
Two component structural grades polymer modified reinstatement mortar

Principal Use
For the reinstatement of concrete in small localized patch repair

Key Properties

Compressive @ 28 days :   45 N/mm²
Flexural strength @ 28 days: 8N/mm²
 
 Advantages:

  • High strength

  • Can be applied by hand, like conventional mortars

  • Extremely low permeability provides maximum protection against carbon dioxide and chlorides

  • Excellent bond to the concrete substrate

  • Shrinkage compensated

  • No site batching required, supplied in pre-weighed prepacked condition

  • Only addition of water at site to be made while mixing the powder and liquid parts

  • Contains no chlorides.


Specification


Renderoc S2 is supplied as a grey powder along with a liquid polymer and has to be mixed with water on site to produce a highly consistent, high strength repair mortar.

Cement Based Repair Mortar And Concrete

Cement Based Repair Mortar And Concrete
Cement Based Repair Mortar And Concrete

 Cement based repair mortar and concrete - Renderoc Putty 
Description
Cement based polymer rich putty for wall and celling
Principal Use
To Provide a water resistant smooth finish leveling compound for concrete walls,machionry and brick surface 

Advantages:

  • Suitable for both Internal and external applications

  • Water-resistant

  • Excellent adhesion to host substrate

  • Smooth finish

  • Low water absorption

  • Suitable for levelling prior to the application of oil based or water based coatings


Specification


Renderoc Putty is a cement based putty containing selected polymers to provide a smooth finished surface prior to application of decorative coatings. It is available in white and grey colours.

Cement Based Repair Mortar and Concrete

Cement Based Repair Mortar and Concrete
Cement Based Repair Mortar and Concrete

 Cement based repair mortar and concrete - Renderoc RSXtra 
Description
Rapid setting repair concrete 
Principal Use
For emergency reinstatement of damaged or deteriorated concrete
Key Properties
Compressive strength 45N/mm²
Working life              15mins@35ºC 


Advantages:

  • Cost effective - Pioneering ‘DS Technology’ ensures shrinkage control, and enables repairs to be completed ‘right first time

  • Rapid strength gain - Accepts vehicular traffic in 4 hrs.

  • Good durability - High strength, abrasion and weather resistance

  • Economical - Can be ‘bulked-out’ with graded aggregate in some locations.

  • Self compacting - Eliminates honeycombing voids


Specification

Renderoc RSXtra is a blend of dry powders and graded aggregates which requires only the site addition of clean water to produce a highly consistent, high strength, free flowing repair concrete which self-compacts, Renderoc RSXtra exhibits excellent compatibility with concrete and good water repellent properties.

Cement Based Repair Mortar and Concrete - Super Patch

Cement Based Repair Mortar and Concrete - Super Patch
Cement Based Repair Mortar and Concrete - Super Patch

 Cement based repair mortar and concrete – Super patch.

Description

Cementious repair system for cconcrete floors

Principal Use

For patching and replacement of worm out areas filing of holes or depressions in concrete floor slabs in factories godwan commercial or domestic building

Key Properties

Compressive strength    @28days 50N/mm


Advantages:

  • High strength : Nearly three times harder than the normal concrete

  • Non shrink - Eliminates shrinkage problems associated with conventional cement concrete / mortars and ensures effective bonding.

  • Reliability : Factory controlled prepacked product eliminates material selection, quality control and other associated problems on site.

  • Durability : Very high ultimate strengths combined with a uniform microcellular material structure provides heavy duty performance and durability.

  • Early usage : Floor usable in 24 hours for light traffic and in 72 hours for all traffic.

  • Iron free, chloride free : No metallic iron present to corrode and cause staining or deterioration due to rust expansion. Allows early strength development without the use of chlorides.


Specification


Superpatch mortar is supplied as a ready to use dry powder requiring only the addition of water to produce a high strength mortar with non shrink property. The material is a mixture of specially processed cement and carefully graded fine aggregate. Additives impart controlled expansion characteristics and reduce water necessary to produce cohesive mortar mix.

Cement Based Repair Mortar And Concrete - Renderoc UW

Cement Based Repair Mortar And Concrete - Renderoc UW
Cement Based Repair Mortar And Concrete - Renderoc UW

 Cement based repair mortar and concrete - Renderoc UW

Description

Antiwashout non shrink high strength cementious micro concrete for underwater repair.

Principal Use

Rendroc UW micro concrete shall be used as a free flow or pumped material to repair deteriorated or underwater or tidal zone concrete structures without significiant wash out of the cement phase.

Key Properties

Compressive strength            53N/mm²

Flexural Strength                    6.5 N/mm²


Advantages:

  • Shrinkage compensation : Gaseous expansion system compensates for shrinkage and settlement in the plastic state, associated with conventional cement repair materials.

  • Anti wash out : No risk of significant wash-out of cement phase when placed under water. Displaces water effectively.

  • Low porosity : Better steel protector than concrete.

  • High bond strength : No primer required.

  • High early strength : Facilitates rapid installation and early operation of plant.

  • Durability : High early and ultimate strength combined with exceptional resistance to attack by freeze/thaw cycling.

  • Reliability : Factory controlled, prepacked components. Only the addition of water is required on site.

  • Chloride free : Composition allows high early strength development without the use of chlorides.

Specification

Renderoc UW is supplied as a ready to use dry powder requiring only the addition of water to produce a free flowing,

Cement Based Repair Mortar And Concrete - Renderoc Hsxtra

Cement Based Repair Mortar And Concrete - Renderoc Hsxtra
Cement Based Repair Mortar And Concrete - Renderoc Hsxtra

 Cement based repair mortar and concrete-Renderoc HSXtra.

Description

Dual shrinkage controlled,polymer modified,cementious fibre reinforced high specification repair mortar system

Principal Use

Rendroc HS extra is suitable for hand and spray application for repair where high load bearing is required.

Key Properties

Compressive strength                          >70N/mm²

Tensile strength                                    >4N/mm²

Flexural strength                                   > 9N/mm²


Advantages:

 

This in turn leads to a series of associated benefits :

 

  • Cost effective - shrinkage control enables repairs to be completed ‘right first time’

  • Enhanced durability - works in tandem with extremely low permeability to prolong effective working life

  • Compatibility - aligns performance closer than ever before, to that of host concrete

  • User friendly - specifically developed to provide an easy to-apply product, suitable for local conditions

  • Definable performance - positive benefits are easily demonstrated via a single, simple measurement


Specification


Renderoc HSXtra is supplied as a ready to use blend of dry powders, which requires only the addition of clean water to produce a highly consistent, repair mortar suitable for structural concrete and masonry repairs. Renderoc HSXtra may be hand applied or sprayed with suitable equipment, please see application method statement for details.

Polyester Resin Mortar and Concrete - Nitomortar PE

Polyester Resin Mortar and Concrete - Nitomortar PE
Polyester Resin Mortar and Concrete - Nitomortar PE

  Nitomortar PE.

Description

High strength jointing and multi purpose repair compound

Principal Use

For fast and emergency reinstatement of concrete bedding jointing and reprofilling of concrete masonry and brickwork.These product are mainly useful where fast strength gain is important.

Key Properties

Compressive strength at 7D       100N/mm²
Flexural Strength                         28 & 25 N/mm² respectivelly
Tensile strength                           14 & 12N/mm²respectively
  
Advantages:

  • Fast development of strength minimises disruption -stronger than concrete within 2 hours

  • No primer required - excellent bond to a wide variety of substrates

  • High chemical and oil resistance

  • Extremely versatile - can be poured, trowelled or modified with aggregate without significantly affecting setting times or strengths

  • Extremely low wastage due to ability to mix part packs to consistencies required

  • W ill cure under damp or wet conditions and can be used down to 0°C

  • Pre-weighed components ensure consistency


Specification


Nitomortar PE products are based on a polyester resin system. There are two grades: Nitomortar PE - for general purpose use; Nitomortar PE Concrete - a special grade allowing users to add suitable aggregate, thereby substantially reducing the cost of infilling larger voids.

PU Base Grout Nitofill WS 60

PU Base Grout Nitofill WS 60
PU Base Grout Nitofill WS 60

 PU base grout for crack injection -Nitofill WS60. 

Description

Rapid foaming and setting resin for stopping flow of water

Principal Use

Stops the flow of water when injected into cracks in concrete in the presence of moving water Nitofill UR 63 provides an effective system for crack sealing wet condition

 


Advantages:

  • Seals against water: Reacts and produces foam resistant to water

  • Rapid acting :Rapid reaction to produce water stop in presence of flowing water

  • Reinjectable :Can be reinjected with Nitofill UR63 to produce a permanent seal.

 

Specification

NitofillWS60 is a two part liquid polyurethane when mixed in the proportions supplied it reacts rapidly with water to form a foam barrier.

Epoxy Based Repair Mortar and Concrete - Expocrete EC

Epoxy Based Repair Mortar and Concrete - Expocrete EC
Epoxy Based Repair Mortar and Concrete - Expocrete EC

 Epoxy based repair mortar and Concrete - Expocrete EC.
Description

High strength epoxy concrete.

Principal Use

For fast and permanent reinstatement of concrete Particularly where high strength abrasion impact and chemical resistance are required.The product is designed for horizental application and reinstatement of defective concrete surface

Key Properties

Pot life at 35ºC            30min

Compressive strength    90N/mm³

Bond strength                 3N/mm³

Advantages:


  • Solvent free

  • Dimensionally stable hardening

  • High compressive and abrasion strengths

  • Curing unaffected by humidity

  • Suitable for both damp and dry surfaces

  • Rapid hardening at low temperatures

  • Impact resistant


Specification


Expocrete EC is a solvent free, epoxy based repair concrete, which is supplied as three component system and the coarse aggregate in the ratio recommended to be added at site.

Expocrete EPW

Exporete EUW

Description

High strength under water flexible epoxy concrete

Principal Use

For fast and permament reinstatement of concrete particularly where high strength abrasion impact and chemical resistance are required.The product is designed for horizental application and reinstatement of defective concrete surface

Key Properties
Pot Life at 27ºC                30-40mins
Flow as per BS come         18-19cm
Compressive strengthTD
Under water curing            80N/mm²
Air curing                            100N/mm² 
Feature & Benifits
   
  • Most suited for underwater applications

  • Solvent free

  • Dimensionally stable hardening

  • High compressive and abrasion strengths

  • Curing unaffected by humidity

  • Suitable for both damp and dry surfaces

  • Rapid hardening at low temperatures

  • Impact resistant


Specification


Expocrete EUW is a solvent free, epoxy based underwater repair concrete, which is supplied as three component system.

PU Base Grout

 PU base grout for crack injection - Nitofill UR 63.

Description

Solvent free two part polyurethene resin for sealing cracks

Principal Use

Can be injected into cracks in concrete or masonry in dry or damp condition to form an elastic seal.caution must be exercised with cracks which are live or filled with dust water or salt It can be used to seal cracks in wet condition in basement tunnel etc.

Key properties

Pot Life 25ºC                  35mins

Reaction Times at 25ºC    95mins

Advantages:

  • Low viscosity : Penetrates fine cracks and cavities.

  • Good adhesion: Adheres strongly to dry or moist concrete

  • Flexible: Strong but flexible to withstand differential structural movement

  • Tough : Withstands high hydrostatic pressures

  • Impermeable: On curing it forms a hard mass impermeable to water

  • Suitable for use in high temperature conditions.


Sepecification

  • Nitofill UR63 is a two part liquid polyurethane. When mixed in

  • The proportion supplied they react to form a tough, slightly

  • Flexible resin. Nitofill UR63 has a good adhesion to concrete and masonry and when injected into cracks it allows some

  • Movement without loss of bond.

Cement Based Repair Mortar And Concrete - Renderoc FC

Cement Based Repair Mortar And Concrete - Renderoc FC
Cement Based Repair Mortar And Concrete - Renderoc FC

 Cement based repair mortar and concrete - Renderoc FC

Description

Single compound polymer modified cementious pinhole filer

Principal use

 Rendroc Fc is designed for application to minor imperfection in concrete and masonry surface

Key Properties

Compressive strength     20N/mm²

Fresh wet dwnsity            200kg/m³

Advantages:

  • Cost effective - no independent primer necessary

  • Time saving - curing not necessary

  • High performance - excellent bond to the substrate


Cement Based Repair Mortar And Concrete - Patchroc

Cement Based Repair Mortar And Concrete - Patchroc
Cement Based Repair Mortar And Concrete - Patchroc

 Cement based repair mortar and concrete – Patchroc

Description

Medium fast setting oncrete patching compound

principal use

Patchroc has been specially designed to provide a fast set repairin concrete floors and is partcullarly useful where traffic must be kept flowing with minimum down time

Key Properties

Working life          20 min@ 30ºC

Seeting time          40 min@30º

Compressive strength    40N/mm²

Advantages:

  • Medium Fast setting - Minimum disruption to traffic

  • Easy to use - Needs only the addition of water.

  • Easy to lay - Very easy to apply & finish

  • Non shrink - Does not crack

  • High adhesion - Use Nitobond AR as primer ensures good bonding to concrete substrates.

  • Durable & Tough surface - Resistant to wear and tear

 

Epoxy Based Repair Mortar And Concrete - Exposeal UW

Epoxy Based Repair Mortar And Concrete - Exposeal UW
Epoxy Based Repair Mortar And Concrete - Exposeal UW

Epoxy based repair mortar and Concrete - Exposeal UW.

Description
Epoxy resin based putty for underwater repairs
Principal Use
For filling of blow holes,sealing of cracks underwater grouting eliminating minor irregularities on concrete surface in damp and under water condition.
Key Properties
Pot Life 30ºC              30 mins
Compressive strength    45 N/mm²
Drying time at 30ºC        16 hours
Full cure at 30ºC              7Days   
 Advantages:

  • Easy mixing of base and hardener in 1:1 by weight

  • Easy to apply and finish

  • Non-slump, can be applied to vertical surfaces

  • Chemical resistant

  • Good adhesion to damp concrete

  • Cures in submerged conditions without shrinkage



Cement Based Repair Mortar And Concrete - Renderoc HB2

Cement Based Repair Mortar And Concrete - Renderoc HB2
Cement Based Repair Mortar And Concrete - Renderoc HB2

Rendroc HB 2
Description
Two component high built polymer modified cementious reinstateent mortar
Principal use
Rendroc HB 2 is a cementious repair compound which is used to reinstate damaged and deteriorated concrete
Key Properties
Compressive strength    20N/mm
Tensile strength             1.7N/mm
Flexural strength             4.5N/mm
 Advantages:

  • In vertical and overhead situations, a high thickness can be built up.

  • Extremely low permeability provides maximum protection against carbon dioxide and chlorides.

  • Excellent bond to the concrete substrate

  • Shrinkage compensated

  • Only addition of water at site to be made while mixing the powder and liquid parts

  • Contains no chloride admixtures



Epoxy Based Repair Mortar And Concrete - Nitomortar FC

Epoxy Based Repair Mortar And Concrete - Nitomortar FC
Epoxy Based Repair Mortar And Concrete - Nitomortar FC

 Epoxy resin based grout for crack injection - Nitomortar FC

Description
High strength jointing and multi-purpose repair compound
Principal Use
 For fast and emergency reinstatement of concrete,bedding,jointing and reposfilling of concrete,masonry and brickwork.these product are mainly useful where fast strength gain is important.
Key Properties
 
Compressive strength at TD      100N/mm² Nitomortar PE & Nitomortar Concrete.
Flexural Strength                      26 & 25N/mm² respectively
Tensile strength                        14 & 12N/mm² respectively 
 
Advantages:

  • Cost effective - Reduces usage of subsequent coatings

  • High performance - Excellent chemical resistance, strong adhesion to concrete substrate

  • User friendly - Easy to apply and finish, manufactured to meet local conditions



Cement Based Repair Mortar and Concrete - Renderoc Plug

Cement Based Repair Mortar and Concrete - Renderoc Plug
Cement Based Repair Mortar and Concrete - Renderoc Plug

 Cement based repair mortar and concrete-Render Plug. 

Description

cementious repair system for concrete floors

Principal Use

For patching and replacement of worm out areas.Filling of holes or depressions in concrete floor slabs in factories,godwans,commercial or domestic building.

Key Properties

COmpressive strength @28days : 60N/mm²

Advantages:

  • Emergency water - stopping capability

  • Single component - only the addition of clean water is required.

  • Excellent bond to the substrate

  • Low exotherm minimises thermal cracking

  • Pre-packed formulation to overcome variation in site batching

  • Contains no chloride admixtures.



Cement Based Repair Mortar And Concrete - Renderoc RG

Cement Based Repair Mortar And Concrete - Renderoc RG
Cement Based Repair Mortar And Concrete - Renderoc RG

 Cement based repair mortar and concrete - Renderoc RG. 

Description

General Purpose,Non strink,Cementious Concrete

Principal Use

Rendro RG is used for repairs to damaged reinforced concrete elements particularly where access is restricted and  where vibration of the placed material official of impossible.

Key Properties

Compressive Strength@28days :  50N/mm³

Fresh net density :           2100-2200kg/m³


Advantages:

  • Gaseous expansion system compensates for shrinkage and settlement in the plastic state.

  • Can be pumped or poured into restricted locations.

  • Highly fluid to allow for placement without vibration.

  • Pre-packed to overcome site-batched variations.

  • Rapid strength gain to facilitate early reinstatement.

  • High ultimate strengths and low permeability of cured repair.

  • Contains no chloride admixture.


Nitozinc Primer

 Nitozinc Primer

Description

Two component epoxy zincrich primer

Principal Use

Is recommended for priming exposed steel reinforcement for use with Fosroc concrete repair mortar.

Key Properties

Pot Life :30 min@30ºC

Specific gravity :   1.75g/cc


Advantages: 

  • Anti corrosive
  • Two component product
  • Timesaving :  Touch dry after 30 to 45 min
  • Excellent adhesion



Galvashield LJ

 

We are the suppliers and the traders of the Galvashield LJ. These are offered to reinstate and actively protect reinforced concrete/structural steel elements subject to the most severe exposure conditions. Typical applications include columns and piles subject to wet-dry tidal cycling in marine environments.


Advantages:


  • Cost effective - The concrete repair and protection carried out at the same time

  • Zero maintenance - No post installation maintenance required

  • Proven technology - with measured performance in aggressive environments

  • Self powered and self regulating - no damaging o v e r -protection

  • Long lasting - 10 - 35 years service life

  • Measurable - Performance can easily be monitored if required.

  • User friendly - Quick, easy and low cost installation

  • Structure specific design - Each system is tailored to the environment and service life expectations

  • Versatile - Can be used to protect conventionally reinforced or prestressed concrete


Description:

 

Galvashield LJ is designed to provide a cost effective, reliable method of reinstating and Cathodically Protecting severely exposed reinforced concrete / structural steel elements. Galvashield LJ is composed of a prefabricated fibreglass jacket lined with expanded zinc mesh conforming to ASTM B69-01a for A190 alloy.

Epoxy Based Repair Mortar And Concrete - Nitocote Putty

We are one of the suppliers of the Epoxy based repair mortar and Concrete - Nitocote Putty. These resin mortars are formulated using premium quality materials and possess very good strength properties. Featuring fast-setting and negligible shrinkage, these are widely recommended for all factories, like fertilizers, paper and textiles. These are available in the market at reasonable prices.


Advantages:

  • Smooth surface

  • Good Coverage for all types of voids

  • Rapid drying

  • Easy to apply

  • Excellent bonding to moist building surface

  • Ability to apply at relatively high thickness.


Description:


Ready to use white paste on most building surfaces. It gives high quality, even surface for painting. Nitocote Putty is specifically manufactured for the painter.

Epoxy Resin Based Grout For Crack Injection - Nitofill Eplv

Advantages:

  • Low viscosity - Can be injected into fine cavities and narrow gaps.

  • High mechanical strength - Performs even under heavyloads and stresses.

  • Excellent adhesive strength - Good bonding with substrate

  • Two part system - Easy to mix and handle

  • Non shrink - Complete filling of voids and cracks

  • Chemical resistant - Can be used in aggressive environments.

     

Description:


Nitofill EPLV is a two part system comprising of liquid base and hardener. It is designed for injecting into narrow gaps, cracks and voids ranging from 0.25mm to 9mm.

Fibre & Plates For Strengthening - Nitowrap 40

We are the famous suppliers and service providers of the Fibre & Plates for strengthening - Nitowrap 40. is used for increasing load carrying capacity of structural members particularly where increase in live load / traffic loads is expected. It can also be used to repair when damage to structural member has occurred due to rebar corrosion, earthquake, fire etc. These are offered in the market at legitimate prices.


Advantages: 

  • Excellent squeezability

  • High bond strength

  • Fast cure

  • Tolerant to damp surfaces

  • Wide range of temperature applications


Description:

 

Nitowrap 40 thixotropic epoxy adhesive is a 2 pack solvent free epoxy resin system consisting of a white base and black hardener in preweighed quantities for easy onsite mixing.

Fibre & Plates For Strengthening - Nitowrap CFP

We are one of the prominent suppliers of the Fibre & Plates for strengthening - Nitowrap CFP. These products are highly demanded in the market because of its durability and efficiency. Our products can also be obtained in the market according to the requirements of the customers and also have many applications in different fields.


Advantages:

  • Very high strength to thickness or weight ratio – Appreciable increase in strength and load carrying capacity without significant increase in dead load.

  • Enhanced stiffness, shear, tensile & torsional capacities - Increased load carrying capacity and better resistance toseismic forces and deflection.

  • Chemical resistant - excellent resistance to acids and alkalis

  • Thin sections - Can be effectively used in space constrained areas

  • Economical - Easy to install, time & labour saving


Description:


Nitowrap CFP is a composite fibre system where Nitowrap CFP carbon strip is used in conjunction with an epoxy adhesive, Nitowrap 40. The system can be protected by a UV resistant coat of Nitowrap 512 in case of atmospherically exposed structures.

Fibre & Plates For Strengthening - Nitowrap EP CF

Our clients can avail a wide range of Fibre & Plates for strengthening - Nitowrap EP CF which is widely appreciated by our clients across the nation. These are fabricated using high quality raw material and the latest advancements in the industry according to specifications of our clients. Our range is well known for high durability and optimum performance.


Advantages:

  • Very high strength to thickness or weight ratio – Appreciable increase in strength and load carrying capacity without significant increase in dead load

  • Enhanced stiffness, shear & tensile capacities – Increased load carrying capacity and better resistance to seismic

  • forces and deflection.

  • Chemical resistant – Excellent resistance to acids and alkalis

  • Flexible- Can be applied on any shape or contour of substrate

  • Thin sections - Can be effectively used in spacecon strained areas.

  • Creep & Fatigue resistance - Ideal for conditions of sustained loading and repeated loading.

  • Economical- Easy to install, time & labour saving


Description:


Nitowrap EP(CF) is a carbon fibre composite wrapping system where Nitowrap EP(CF) is used in conjunction with an epoxy sealer cum primer, Nitowrap 30 and a high build epoxy saturant Nitowrap 410. The system is protected by a polyurethane top coat of Nitowrap 512 in case of atmospherically exposed structures.

Fibre & Plates For Strengthening - Nitowrap EP GF

We present an exclusive range of Fibre & Plates for strengthening - Nitowrap EP GF to our clients. Our product is a glass fibre composite wrapping system where it is used in conjunction with an epoxy sealer cum primer, Nitowrap 30, and a high build epoxy saturant Nitowrap 410. The system is protected by a polyurethane top coat of Nitowrap 512 in case of atmospherically exposed structures.


Advantages:


  • Very high strength to thickness or weight ratio – Appreciable increase in strength and load carrying capacity without significant increase in dead load

  • Enhanced stiffness, shear & tensile capacities – Increased load carrying capacity and better resistance to seismic forces and deflection.

  • Chemical resistant – Excellent resistance to acids and alkalis

  • Flexible- Can be applied on any shape or contour of substrate

  • Thin sections - Can be effectively used in space constrained areas.

  • Economical- Easy to install, time & labour saving

 

Description:

 

Nitowrap EP(GF) is a glass fibre composite wrapping system where Nitowrap GF is used in conjunction with an epoxy sealer cum primer, Nitowrap 30, and a high build epoxy saturant Nitowrap 410. The system is protected by a polyurethane top coat of Nitowrap 512 in case of atmospherically exposed structures.

Fibre & Plates For strengthening -Nitowrap FRP600

We are dedicatedly engaged in supplying and service providing a matchless range of Fibre & Plates for strengthening - Nitowrap FRP600. is a carbon fibre composite system for strengthening columns, beams and slabs of load bearing structures particularly where improvement to shear strength and deformation characteristics is required.


Advantages:

  • Very high strength to thickness or weight ratio – Appreciable increase in strength and load carrying capacity without significant increase in dead load

  • Enhanced stiffness, shear & tensile capacities – Increased load carrying capacity and better resistance to seismic forces and deflection.

  • Chemical resistant – Excellent resistance to acids and alkalis

  • Flexible - Can be applied on any shape or contour of substrate

  • Thin sections - Can be effectively used in space constrained areas.

  • Creep & Fatigue resistance - Ideal for conditions of

  • sustained loading and repeated loading.

  • Economical - Easy to install, time & labour saving


Description:


Nitowrap FRP600 is a carbon fibre composite wrapping system where Nitowrap FRP600 is used in conjunction with an epoxy sealer cum primer, Nitowrap 30 and a high build epoxy saturant Nitowrap 410. The system is protected by a polyurethane top coat of Nitowrap 512 in case of atmospherically exposed structures.

Fibre & Plates

We are the suppliers of Fibre & Plates for strengthening - Nitowrap UW. is a glass fibre composite system for strengthening & retrofitting of load bearing structures particularly where enhancement of axial load, shear & flexural strength is required. It is ideal for seismic retrofitting also. Typical applications include piers, columns, beams, retaining walls, piles, tunnels, etc which are either fully or partially underwater.


Advantages:

  • Very high strength to thickness or weight ratio – Appreciable increase in strength and load carrying capacity without significant increase in dead load

  • Enhanced stiffness, shear & tensile capacities – Increased load carrying capacity and better resistance to seismic forces and deflection.

  • Chemical resistant – Excellent resistance to acids , alkalis chlorides etc.

  • Flexible- Can be applied on any shape or contour of substrate

  • Thin sections - Can be effectively used in space constrained areas.

  • Economical- Easy to install, time & labour saving

  • Resistant to biological growth like fungus, algae, barnacle etc.


Description:


Nitowrap UW is a glass fibre composite wrapping system where Nitowrap GF is used in conjunction with a high build under water epoxy saturant Nitowrap 410 UW.


RK Flooring Systems Private Limited

Mr. Ramesh Yadav
Plot No. 166H, Sector- 07, Phase-II, HSIIDC, IMT, Manesar
Gurgaon - 122 001
Haryana, India
© RK Flooring Systems Private Limited. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited