RK Flooring Systems Private LimitedRK Flooring Systems Private Limited

Products & Services



Showcase Gallery
Home » Joint Sealants

Joint Sealants

We offer a Wide range of Joint Sealant is offered by us, which is made in compliance with the specific industrial norms and standards. These sealants are made using high quality material of superior quality sourced from authentic and reliable market vendors. These are available in various specifications based on the requirement of the client.

Joint Sealants

Joint Polyethylene Board & Back Up Rod - Hydrocell Xl

Joint Polyethylene Board & Back Up Rod - Hydrocell Xl

 Joint Polyethylene board & back up rod - Hydrocell XL

Description

High performance cross linked closed cell non absorbent polyethyne joint filler

Principal Use

Used by forming expension joints in concrete,brick work.the product provides excellent support to sealent subject to hydrostatic pressure and is particularly recommended for water retaining water or water excluding structure


Advantages:

  • Cross linked to resist lateral and hydrostatic pressure

  • High density support of sealant to prevent adhesion failure

  • Non absorbent closed cell structure

  • High compression recovery

  • Non-extruding

  • Low load transfer to joint edges

  • Non tainting

  • Chemically resistant

  • Natural bond breaker

  • Rot proof





Civil Engineering Sealants - Nitoseal MS600

Civil Engineering Sealants - Nitoseal MS600

 Civil Engineering Sealants - Nitoseal MS600 ,

Description

One Part civill Enggineering sealent for inmersed condition

Principal Use

Suitable for sealing movement joints in building and civill enginnering structure including joints that will be subjects to intermittent or permanent immersion

Key Properties

Solvent content    100%

Colour                Grey Portland stone

MAF                   25% butt joint 50% lap joints   



Advantages:

  • Approved for use in contact with potable water

  • Meets key international standards

  • Resistant to aerobic and anaerobic bacteriological attack

  • Exhibits excellent water resistance

  • Excellent resistance to dilute acids and alkalis

  • Cures to a tough, elastic rubber seal

  • Accommodates continuous and pronounced cyclic movement

  • High resistance to ageing, reduces physical damage due to climatic extremes

  • Single component yet fast rate of cure

  • Can be applied to damp substrates

  • Isocyanate free technology


Specification


Nitoseal MS600 is a one part medium modulus sealant based on hybrid silyl modified polyether technology. It has a fast rate of cure and forms a tough, highly durable and water resistant elastomer. Conforms to the DWI Water Quality Regulations 25(1)(b) for products having a small surface area in contact with water for public supply.



Other Information
  • Packaging Details: Advantages:

    Approved for use in contact with potable water

    Meets key international standards

    Resistant to aerobic and anaerobic bacteriological attack

    Exhibits excellent water resistance

    Excellent resistance to dilute acids and alkalis

    Cures to a tough, elastic rubber seal

    Accommodates continuous and pronounced cyclic movement

    High resistance to ageing, reduces physical damage due to climatic extremes

    Single component yet fast rate of cure

    Can be applied to damp substrates

    Isocyanate free technology

    Description:

    Nitoseal MS600 is a one part medium modulus sealant based on hybrid silyl modified polyether technology. It has a fast rate of cure and forms a tough, highly durable and water resistant elastomer. Conforms to the DWI Water Quality Regulations 25(1)(b) for products having a small surface area in contact with water for public supply.




Pavement Sealants - Nitoseal MS60

Pavement Sealants - Nitoseal MS60

 Pavement Sealants - Nitoseal MS60

Description

one part genral purpose building sealent

Principal Use

Suitable for sealing joints in concrete,brickworks,Block works,perimeter sealing around doors & window and non trafficed floors joint s

Key Properties

MAF    25%


Advantages:

  • Excellent adhesion to most common building materials

  • Single component with fast rate of cure

  • Easy to apply at low temperature

  • Can be applied to damp substrates

  • Environmentally friendly

  • Primer-less for most applications (see “Priming”)

  • Available in a range of colours (see “Properties”)

  • Isocyanate free technology


Specification:


Nitoseal MS50 is a one part, medium modulus sealant based on hybrid silyl modified polyether technology.





Building Sealants - Decofill

Building Sealants - Decofill

 Building Sealants – Decofill

Description

Fast setting flexible acrylic sealent

principal use

Used a wall/celling comices door and window frame surrounds fitted furniture,skirting ,staircases replacement window installation
Key Properties

Form         Paste

Solid Content         85%

Colour               white

MAF                    +_10%

Cure Rate            Approx.  3-5 Days


Advantages:

  • Easy to apply and finish

  • Excellent adhesion to most building materials

  • Fast setting

  • Non-staining

  • Flexible seal

  • Can be over painted or papered


Specification


Decofill acrylic sealant is a white acrylic based gap filler in paste form for application from a cartridge. It is very quick and easy to apply and can be finished or smoothed off with a spatula or a damp sponge. It sets quickly on application and will accept paint or wallpaper finishes.





Civil Engineering Sealants - Nitoseal HP40

Civil Engineering Sealants - Nitoseal HP40

 Civil Engineering Sealants - Nitoseal HP40
Description

One part PU based building & Expansion joint sealent

Principal Use

Nitoseal HP 40 is suitable for sealing joints in concrete brickwork ,precast penels stone cledding perimeter sealing around doors and windows and non trafficked floor joints


Advantages:

  • Adhesion to most common building materials

  • Single component with fast rate of cure

  • Easy to apply

  • UV resistant

  • Primerless for most applications (see “Priming”)

  • Available in a range of colours

  • ISO11600:2002 Type F 25LM compliant


Specification


Nitoseal HP40 is a one part, low modulus gun grade elastomeric sealant based on polyurethane technology. Nitoseal HP40 may be applied to joints between 5 and 35mm wide. To minimise stress imposed on the joint sealant, all moving joints should be designed to an optimum width to depth ratio of 2:1 with an overriding minimum depth of 5 mm for non-porous surfaces and10 mm for porous surfaces.





Expansion Joint Membrane - Expoband One

Expansion Joint Membrane - Expoband One

 Expansion joint membrane - Expoband One

Description

Flexible expension joint membrane

Principal use

Expoband one is hypalon membrane designed to be bonded over movement joints or cracks in structure to pervent the passage of water it is bonded in position using Nitomortar FCFS two part epoxy adeshive Expoband .One is suitable for construction use and in repair remedial application.

Key Properties

Form                       Elastomeric strips

Colour                     Grey

Density                    1.7 approx

Tensile strength        7N/mm²

Elongation               40%

Advantages:

  • Accommodates continuous and pronounced cyclic movement

  • Excellent resistance to weathering

  • Can be applied to dry or damp surfaces


Specification

 

Expoband One is an un-reinforced Hypalon membrane incorporating a central release tape, available in 1mm thickness and widths of 100mm and 200mm. The 1mm thick membrane is supplied in a 25 meter roll.





Pavement Sealants - Colpor 200

Pavement Sealants - Colpor 200

With the help of our experts, we offer Pavement Sealants - Colpor 200 to our clients that are used in various industrial application. Our ranges are highly checked on the various parameters and meet industry standards. These are appreciated for features like unmatched quality, ability to withstand adverse conditions, effectiveness, easy application, flexible sealing property and high strength. Furthermore, we offer our range at industry leading prices.


Advantages:

  • Cold applied - no heating equipment required

  • Fuel, oil and hydraulic fluid resistant

  • Self-levelling

  • Tough rubbery seal

  • High performance - less maintenance


Description:


Fosroc Colpor 200 cold applied, two part polyurethane sealant is designed for joints in concrete paved areas. The capability of accommodating cyclic movements is retained by Colpor 200 throughout extremes of temperature conditions.





Pavement Sealants - Colpor 200PF

Pavement Sealants - Colpor 200PF


 Pavement Sealants - Colpor 200PF

 Description

Coldapplied high performance piltch free,polyurethene pavement joint sealent

Principal Use

For sealing and maintance of horizental joints in concrete roads,concrete runways and hard standing.The excellent fuel resistance of colpor 200 PF makes it perticulerly suitable for sealing areas where fuel and oil spillage might occure such as aircraft fueling areas of terminals parking and warehouse,docks and harbors.

Key Properties

Form          :      Two part compound

Specific Gravity :   1.45g/cc

Full cure        :     5-7days @25ºC

Advantages:


  • Pitch free - environmental friendly

  • Cold applied - no heating equipment required

  • Fuel, oil and hydraulic fluid resistant

  • Self-levelling

  • Tough rubbery seal

  • High performance - less maintenance

Standard complience

Colpor 200 PF complies with IRMRA certification.British Standard 5212 1990-types N.Fand FB

 




Pavement Sealants - Nitoseal 280

Pavement Sealants - Nitoseal 280

 Pavement Sealants - Nitoseal 280

Description

Heavy duty epoxy urethene joint sealent

Principal Use

For sealing internal floor joints subject to heavy industrial use in factories,food processing areas warehouse and maintance facilities.Particularly suitable for sawn joints in long strip flooring and other large internal areas.

Key Properties

VAF    :       10%

Intial cure at 20ºC : 24hrs

Full cure at 20ºc       :       3days

Specific gravity       :  1.31g/cc


Advantages:

  • Load bearing for support of arises under heavy wheel load

  • Good resistance to chemicals and hydrocarbon fuels

  • Excellent adhesion without primer to dry clean concrete

  • Pouring grade ensures ease of placing

  • Suitable for use in wide joints

  • Self levelling to produce uniform and neat joints







Civil Engineering Sealants -Thioflex 600

Civil Engineering Sealants -Thioflex 600


 Civil Engineering Sealants -Thioflex 600

Description

Two part polysulphides sealent available two grades Gun grades and pure grade

Principal use

For use in horizental joints.The product is partiicularly recommended for sealing horizental structral expansion joints in most civill engineering structures like building super structures.Subway,basement,floors & reserevois.

Key Properities

Colour (Mixed material)   :  Grey

Solids Content                : 100%

Density                          : 1.60-1.65kg/ltr


Advantages:
  • Forms a tough elastic rubber-like seal.

  • Accommodates continuous and pronounced cyclic movement.

  • Excellent adhesion to most common substrates.

  • High resistance to ageing influences, physical damage and climatic extremes.


Package
Both Gun Grades & Pureable grade 2.5 Pack




Joint Polyethylene Board & Back Up Rod - Expancell

We take Pride in offering Joint Polyethylene board & Back up rod – Expancell which are used in various applications. These are checked on various parameters to deliver a defect free range. They are highly appreciated by our clients for reliability and high accuracy result. We offer them at cost effective price.


Advantages:

 

  • Economical

  • Easy to install

  • Readily compressible

  • Rot proof and non-absorbent

  • Provides bond breaker and minimum strain shape for joint sealants

  • Provides a firm backing for sealant tooling

 

Description:

 

Expancell polyethylene foam back-up cords have the ability to perform several functions. They enable the correct width to depth ratio of the sealing slot to be maintained and provide a firm backing for the sealant to be tooled. This will precipitate wetting of the sides of the joint during the sealant application thus facilitating good adhesion.







Contact Us

*Describe Your Requirements in Detail
Remaining Characters: 3500
Your Contact Information
Your Contact Information
*Name:
*Email:
Company:
Website:
*Country:

City:
*Mobile:
*Enter the code: